Contact us: +44 116 291 9092
Title Image

Eye One iO automated scanning table review

  |   Articles and reviews, Colour management, Hardware review, Review, X-Rite   |   3 Comments

Eye One iO automated scanning table review

Using the Eye One Pro gets even easier – and more accurate with the iO

[adrotate group=”8″

A device to help speed up profile making and make it more accurate.

We’ve reviewed various versions of the Eye One profiling package elsewhere, and found it easy to use, and capable of very good results when producing icc printer profiles.

i1 pro and iO table

April 2011- Products are now offered with i1 Profiler software
July 2012 – An updated version of the table is available with the i1Pro 2

If you are making more than the odd one or two profiles, then manual measurement can introduce inaccuracies and inconsistencies into your profile making.

The Eye One iO automated scanning table is a USB controlled scanning arm that automates the scanning process.

It holds your i1 spectrophotometer to move it over the target.

If you are making profiles as part of your business, it makes it a lot easier for less skilled staff to carry out the measurement process.

Keith has been looking at what this device from XRite/GretagMacbeth does…

The iO robot arm in action.

xrite / gretagMacbeth iO

What do you get with the iO?

I’ve used the Eye One Pro spectrophotometer with the Eye One Match software for building icc printer profiles for some time.

Note, if you are new to the Eye One system, you might like to read the original Printer Profiling review first.

Update note: We have reviews of most X-Rite products on the site – most of our older articles are still worth looking over, since they often contain relevant background info and tips.

My first Eye One package came with a simple ruler to align the measuring device as you scanned it across a test target

Eye One patch ruler

Original Eye One ruler

You can see that the device has rollers to allow you to step down the paper as you scan it

Eye One target readingNext came the improved scanning table, which both held the target firmly and provided a standard background for your test patch (target) prints.

An additional slide held the back end of the sensor in place, ensuring that you didn’t scrape your target print, and the sensor was kept at a more uniform alignment.

Printer profiling relies on accurate and consistent measurement of the coloured test patches.

With the Eye One match software, you do get the chance to see each row of measurements as they are read in, and the software will spot more serious errors. However it is still dependant on you taking the care to do it right.

Now that’s OK if I’m making just one profile, but what if I want to make half a dozen to try a range of new papers?

I’m interested in colour management and enjoy testing things, however I get bored easily. It’s all to easy to just let a row of measurements be rushed or slightly mis-align the ruler, so I end up with data ‘contaminated’ by a tiny portion of the row above or below.

Remember that one duff measurement can throw out a profile, and in general, the more patches that a target has, the better the profile will be.

So much easier if only you could remove that human element…

The iO robot arm

First of all I have to admit that this is one of the coolest and most impressive bits of colour management kit I’ve got… It’s the one thing that never fails to impress visitors. There is something about the movement of the arm that fascinates people :-)

I’ve had a number of very different careers and this bit appeals to the engineer in me — My printer room has a desk with two big drawers in it, one full of Technics Lego and the other full of Meccano…

OK, back to printer profiling…

Your Eye One spectrophotometer fits into a clear plastic tray. In the photo below you can see the USB plug at the back, that goes into the spectro.

A USB lead then connects the whole device to your computer (the iO also has a small external power supply)

You can also see the white plastic glider ring, that protects the print while being scanned.

fitting Eye one to iO

Fitting the Eye One

The iO handles targets up to 10mm thick, so if you want to profile printed ceramic tiles for example, then no problem.

You can also see the white tile calibration target for the Eye One in the top left corner of the picture. The device rests over this in its ‘rest’ position.

The glider ring is a ‘consumable’ item, and will require replacement after several hundred sheets are measured.

iO glide plate

Spring clips hold the ‘glide plate’ in place (you can see that the scan height is set to a thicker target material)

Using the iO with Eye One Match

In this review I’m looking at just the standard Eye One Match software. I’ve written other reviews showing its use for CameraScanner and Printer profiling.

I’ll be looking at the more advanced ProfileMaker Pro software in some future articles, along with the Eye One iSis measuring device.

The eye one Match software detect the presence of an iO and offers you the opportunity to use it.

using the iO to profile

Using the iO

Since I’ve described the target printing and profile building process in the other Eye One articles, I’ll just show some of the differences you get with the iO here…

I’m going to measure a two (A4) page 918 patch target that I made when testing a new paper on my Epson 1160 – as ever make sure your targets are printed with the correct media settings and allowed to dry properly.

The chart is positioned on the table.

setting target on GMB iO

The table has an electrostatic holding mechanism that uses the same effect as when your hair ‘sticks’ to a comb or a balloon ‘sticks’ to a wall after getting a static charge.

Original ImageHover Image

Mouse over the image to see the effect of the chart hold

The software needs to know where three specific corners of the target are, so it can move the arm to scan the patches

iO test chart positioning

Positioning test chart

A target mark on the sensor holder enables you to precisely locate the corners.

iO chart target

When positioned, you press the side button on the Eye One.

The picture below shows a patch position selected.

iO chart corner

Selecting a corner patch

Once selected, the device just does its stuff…

reading the profiling target

Reading the second page

Note how the readings are displayed as they are taken – line by line

Once finished, the software builds your profile and that’s it…

building the printer profile

Job done…


Very easy to set up and use. Adds an extra element of confidence and accuracy into my profiling workflow.

I tried a wide variety of targets and it just worked…

Makes it that bit easier to do some experimentation when creating profiles, if like me you find manual patch measuring a fundamentally tedious process ;-)

X-Rite/GretagMacbeth and their distributors offer the iO in a range of packages and special deals – so it’s very difficult to give exact pricing – best to see what they or a local reseller is currently offering.


Profiles need accurate repeatable measurements – the iO helps achieve this by automating the process. It is quick and efficient and unlike a human operator, won’t get bored.

In the example above I’ve looked at using the Eye One Match software – if you are using more advanced profiling software, then the accuracy of automated measurement should be even more appreciated, particularly if you are using targets of thousands of patches.

Ideal too, if you have to measure targets printed onto thicker materials such as packaging.

Works on both Macs and PCs, available either on its own, or in conjunction with different level profiling solutions from X-Rite/GretagMacbeth (more details)

Specifications (From manufacturers)


  • Positioning Area: 32 x 23 cm, 12.6” x 9” (Width x Height)
  • Media Thickness: Max. 10 mm, 0.39”
  • Patch Size: Min.: 6 mm x 7 mm (Width x Height)

Chart Measurement

  • Measurement Speed: > 400 patches / Minute, IT8.7/3 chart (924 patches) <= 2.2 minutes
  • Calibration: Automatic on internal calibration reference


  • Interface: USB 1.2
  • Power Supply: Auto rating 100 to 240 VAC, 50 / 60 Hz
  • Physical Dimensions: 510 x 460 x 170 mm, 20 x 18.1 x 6.7 (Width x Depth x Height)
  • Weight: 4.5 kg, 9.9 lb. (without Eye-One Pro device)
  • Environmental: Operating Temperature: +10°C (50°F) to 104°C (°F)
  • Humidity: 0 to 85% RH

Never miss a new article or review - Sign up for our Newsletter (2-4 a month max.)

More colour management and printing related information

For information about printers, paper reviews and profiling (colour management) see the Printing section of the main printers and printing page, or use the search box at the top of any page.
All colour management articles and reviews are indexed on the main Colour Management page - please do let Keith know if you've any questions, either via the comments or just email us?

Some specific articles that may be of interest:  

  • Why don't my prints match my screen? A short article showing why there is more to getting your prints to match your screen, than just calibrating your monitor. It's the vital first step, but you do need to consider some other factors for best results.
  • Why are my prints too dark - some basic suggestions to this common problem.

Articles below by Keith (Google's picks for matching this page)

Site update: Sorry for site slowness - the site has outgrown its hosting. Keith is working on this, but we are photographers not web developers!
...Get our Newsletter for new articles/reviews and why not subscribe to Keith's YouTube Channel
...Keith's book about how to use tilt/shift lenses is now available.
Our site contains affiliate links - these help support the site. See our Advertising policies for more

  • Andreas Strubin | Sep 25, 2017 at 7:33 pm

    Thanks Keith, i do run it on an old PowerMac – will check it out so. sometimes handy keeping aan old machine around:)

  • Keith Cooper | Sep 25, 2017 at 1:52 pm

    The old i1iO will work with i1Profiler, but that’s new software.

    Match used the software key inside the i1 spectro (or dongle) IIRC

    Of course, the old software needs an old computer to run on…

  • Andreas Strubin | Sep 25, 2017 at 12:54 pm

    Real cool and usefully info on the eye-one match. I have one but have lost the software code and X-rite doesn’t support the equipment anymore. Any suggestions??

Post A Comment